AMD CS5535 Guida Utente

AR-B1631ET User’s Guide 1/30 ACROSSER® AR-B1631ET (Extended Temperature) powered by AMD Geode LX800, EPIC SBC with CRT, LCD, LAN, U

AR-B1631ET User’s Guide 10/30 2.2.7 IR1 2.2.8 J3 (CLEAR CMOS) 2.2.9 CN10 (LCD SETTING) 2.2.10 CDIN1 (CDIN) 2.2.11 CN

AR-B1631ET User’s Guide 11/30 2.2.13 J5 (LCD BACKLIGHT) 2.2.14 JP4 (LCD LVDS) 2.2.15 LPT1 (PARALLEL PORT)

AR-B1631ET User’s Guide 12/30 2.2.16 BUZZER EXTERNAL 2.2.17 J4 (PC104+) A1 B1 C1 D1 A30 B30 C30 D30

AR-B1631ET User’s Guide 13/30 2.2.18 JP6 (IDE Cable Select, NOTE 2) 2.2.19 USBA_1 & USBA_2 (NOTE 2) 2.2.20 USB1 & U

AR-B1631ET User’s Guide 14/30 2.2.22 CN4 (RS422 & RS485) 2.2.22 CF1 (NOTE 1) NOTE 1: For using both Hard Disk and Compact F

AR-B1631ET User’s Guide 15/30 3 LCD FLAT PANEL DISPLAY This chapter describes the configuration and installation procedures for LCD displays.

AR-B1631ET User’s Guide 16/30 4 BIOS CONSOLE This chapter describes the AR-B1631ET BIOS menu displays and explains how to perform common tasks n

AR-B1631ET User’s Guide 17/30 The <Main> option allows you to view some basic system hardware configuration and to set the system clock as w

AR-B1631ET User’s Guide 18/30 Video Memory Size [8M] Configuration options: [None] [8M] [16M] [32M] [64M] [128M] [254M] Output Display [CRT] This

AR-B1631ET User’s Guide 19/30 4.4 PnP/PCI PnP/PCI Reset Configuration Data [Disable] Normally, you leave this field Disabled. Select Enabled to

AR-B1631ET User’s Guide 2/30 Contents 1 INTRODUCTION ... 4 2 SYSTEM SETUP ...

AR-B1631ET User’s Guide 20/30 Onboard Serial Port 1 [3F8/IRQ4] Choose the serial port 1 I/O address. Do not set port 1, 2, 3 and 4 to the same add

AR-B1631ET User’s Guide 21/30 OnChip IDE Device With this option you can enable or disable your IDE channel and set the PIO mode or UDMA mode. 4

AR-B1631ET User’s Guide 22/30 4.7 BIOS EXIT Exit When you have made all of your selections from the various menus in the Setup program, save yo

AR-B1631ET User’s Guide 23/30 5 I/O ADDRESS, IRQ AND MEMORY MAPPING 5.1 I/O ADDRESS MAPPING

AR-B1631ET User’s Guide 24/30 5.2 IRQ MAPPING 5.3 MEMORY MAPPING

AR-B1631ET User’s Guide 25/30 6 GPIO SAMPLE CODE /*[]=====================================================================[]*/ /*|| GPIO Test ut

AR-B1631ET User’s Guide 26/30 /////// Input High Test /////////////////////////////////////////////////// printf("\nConnect GPI

AR-B1631ET User’s Guide 27/30 Show_Byte=Show_Byte|0x04; else Show_Byte=Show_Byte&0xFB; if(Read_Byte&0x08) //GPI13 Show_B

AR-B1631ET User’s Guide 28/30 // Set W83627HF GPIO10~17 to Low outportb(IO_PORT_BASE,0xF1); outportb(IO_PORT_BASE+1,0x00); print

AR-B1631ET User’s Guide 29/30 return(0); } /*[]=====================================================================[]*/ /*|| Function : Sho

AR-B1631ET User’s Guide 3/30 4.5 PERIPHERALS...19 4.6 BOOT...

AR-B1631ET User’s Guide 30/30 void Enter_Config(BYTE IO_PORT_BASE) { outportb(IO_PORT_BASE,0x87); outportb(IO_PORT_BASE,0x87); } /*[]========

AR-B1631ET User’s Guide 4/30 1 INTRODUCTION Welcome to the AR-B1631ET Single Board Computer, the AR-B1631ET low power AMD Geode LX800 processor

AR-B1631ET User’s Guide 5/30 (24Bit)lvdsCrystalFlashLPC BUSPCI(33/66 MHz)(SST FWH)(CS5535/CS5536)66 MHzUSB x 248 MHzCOM1ANDCOM2SynthesizerPCI BUS(

AR-B1631ET User’s Guide 6/30  Power Req.: +5V 2A and +12V 1A maximum  PC Board: 6 layers, EMI considered  GPIO: 8pin (4 output and 4 input

AR-B1631ET User’s Guide 7/30 2 SYSTEM SETUP This chapter describes how to install the AR-B1631ET. At first, the layout of the AR-B1631ET is sho

AR-B1631ET User’s Guide 8/30 2.2 SYSTEM SETTINGS Jumper pins allow you to set specific system parameters. Set them by chan

AR-B1631ET User’s Guide 9/30 2.2.3 DIO1 (GPIO) 2.2.4 AUDIO1 (AUDIO) 2.2.5 COM2, COM3, COM4 (RS232) 2.2.6 J2 (CHASSIS